Product

KTC1 series is the company combined with more than ten years of manufacturing experience and customer feedback, by the engineering department and R & D department to optimize and improve, product appearance, internal structure, material, production process, technical parameters and sealing grade parameters have been greatly upgraded, raw materials are imported with original. Production and manufacturing fully adopt the current international industry more advanced technology and process, the product after 100 million times of reciprocating movement life test, the performance indicators and technical parameters are still in line with the industry higher standards. The signal output terminal and wire plate connection device obtained the utility model patent, and the product appearance obtained the design patent.

KTC1拉杆式直线位移传感器电阻尺注塑机拉杆电子尺

Scope of application：KTC1 is a general type, suitable for the position detection of various types of equipment, such as: injection molding machine, die casting machine, rubber machine, shoe machine, EVA injection molding machine, hollow bottle blowing machine, woodworking machinery, hydraulic press, etc.

Standard technical parameters：

Note: The values of linearity, service life, etc. listed in the following data table are the values of the sensor operating with the operational amplifier as the voltage output voltage to the slip brush, and

It is obtained when there is no load on the sliding brush (l e≤ 10 μA).

	KTC1 Universal pull rod series	50~110mm	125~175mm	200~550mm	600~1250mm	Range selectio-n reference: unit: mm 50 75 100 110 125 130 150 175 200 225 250 275 300 325 350 360 375 400 425 450 475 500 550 600 650 700 750 800 850 900 950 1000 1150 1250
Electrical parameter	Linearity（±%）	0.1	0.05	0.05	0.05
	Resistance tolerance±10 %	5.0KΩ		10.0KΩ
	Electrical travel	Stroke+3mm
	Resolution	Infinite Unbroken analysis
	Repeatability	0.01mm
	Normal working current of sliding brush	≤10μA
	A larger current that causes the brush to slip when it fails	10mA
	Max allowable operating voltage	42V
	Effective temperature coefficient ratio of output voltage to input voltage	Usually 5ppm/K
	Insulation impedance( 500VDC )	≥10MΩ
	Insulation strength（500VAC,50Hz）	≤10 0μA
Mechanical parameterS	Shell length（A）	Stroke+78.5mm
	Mechanical travel（B）	Stroke+8mm
	The pull rod carries more tension	50KG
	Working force	Horizontal direction＜10N
		Vertical direction≤10N
Environmental parameter	Anti-vibration standard	5...2000Hz , Amax=0.8mm , amax=20g
	Impact resistance standard	50g ,11ms
	Operating temperature range	-60...+150℃
	Life	＞100 x 106次
	Max operating speed	10m/S ,Greater operating acceleration 10m/s²
	IP	IP67(DIN40500/IEC529)

KTC1 Installation dimension drawing：

KTC1拉杆式直线位移传感器电阻尺注塑机拉杆电子尺

KTC1(LWH) installation instructions and schematic diagram：

When positioning the sensor, ensure that it is locked in the horizontal state；
The screw hole of the traction support and the sensor tie rod must be concentric；

安装注意1.png
安装注意2.png

QQ图片20240103135744.png

Output type of KTC1 pull-rod resistance ruler：

Resistance output type：5kΩ，10KΩ，

Voltage output type (external/built-in module)：0-5V，0-10V，

Current output type (external/built-in module)：4-20MA (two wires，three wires），

Digital signal (external/built-in module)：RS485。

Application range of KTC1 pull-rod resistance gauge：

Application: KTC is a general type, suitable for position detection of various types of equipment, such as: injection molding machine, die casting machine, rubber machine, shoe machine, EVA injection molding machine, hollow bottle blowing machine, woodworking machinery, hydraulic press, etc.

For more information and specific prices, please call our service hotline：+86 18988775298 Mrs Yuki

Application

Prev：玉树KST Self resetting displacement sensor

Next：玉树KPM12R1/KPM12R2 Self-reset Resistance Sensor