MTF1/MTF2 Slider Magnetostrictive Displacement Sensor Overview:
The change in the direction of magnetization in the ferromagnetic material will cause the change in the lattice spacing of the medium, so that the length and volume of the ferromagnetic material will change, that is, the magnetostriction phenomenon, also known as the Wiederman effect, and its inverse effect is called the Villari effect.
The principle of magnetostrictive displacement sensor is to generate a strain pulse signal when two different magnetic fields intersect, and then calculate the time period required for this signal to be detected, so as to convert the accurate position. The two magnetic fields, one from the permanent magnet in the magnetic ring, and the other from the excitation pulse generated by the electronic components in the sensor's electronic compartment. The excitation pulse travels at the speed of sound along a waveguide filament made of magnetostrictive material inside the sensor. When intersecting with the permanent magnet field in the magnetic ring, the mechanical vibration generated by the waveguide wire forms a strain pulse due to magnetostriction. The strain pulse is quickly detected by a sensing circuit in the electronic chamber. From the moment when the excitation pulse is generated to the total time when the strain pulse is detected by a fixed sound speed, we can accurately calculate the position change of the magnet. This process is continuous, so whenever the position of the magnetic ring changes, the new position is quickly measured. Since the output signal is a true position value, rather than a proportional or reamplified signal, there is no signal drift or variation, let alone the need to periodically re-label as with other sensors.
Magnetostrictive sensors are non-contact and never wear out. It has the advantages of high resolution, high precision, high stability, high reliability, fast response time and long working life. Sensors do not need to be re-calibrated or regularly maintained.
MTF1/MTF2 slider type magnetostrictive displacement sensor technical parameters:
1.Measuring range :80 ~ 3000mm
2. Power supply voltage: +12VDC to +24VDC
3. Output form/analog signal: current 4-20mA and 0-20mA, voltage 0-5V and 0-10V,
Digital signal: RS485, MODBUS-RTU, CANopen, Start-stop,Ether CAT
4. Load capacity: voltage signal output load ≥4KΩ Current signal output load ≤500Ω
5. Nonlinear error :≤0.05%FS
6. Repeatability error :≤0.005%FS
7. Resolution :≤0.038mm
8. Hysteresis :≤0.001%FS
9. Temperature stability: ≤0.002%/℃
10. Working current: ≤16mA
11. Working pressure: continuous working pressure ≤35MPa
12. Working temperature : -40 ~ +80℃,
13. Electronic warehouse shell material :0Cr18Ni9 (304) 316 stainless steel (special custom)
14. Lead mode: high temperature resistant twisted pair shielded cable (default length: 1m, can also be provided according to user requirements)
15. Shell protection grade: IP65, IP67
MTF1/MTF2 slider type magnetostrictive displacement sensor wiring mode:
Before connecting cables, check whether the power supply meets the following requirements: +24VDC and the output power of the power supply must be greater than the total power consumption. The output power of each sensor must be less than or equal to 95mA in different ranges. If electricity
1、Sensor power supply contacts: ①positive power supply (brown) ②/ ③negative power supply ④/2、Sensor EtherCAT contacts: IN ①TX+、②White RX+、③TX-、④RX- OUT ①TX+、②White RX+、③TX-、④RX- MTF1/MTF2 Slider Magnetostrictive displacement sensor Applications:
Servo hydraulic cylinder piston position preset and feedback, servo cylinder piston position preset and feedback, grinding machinery position preset and feedback, casting and forging machine position preset and feedback, other machinery such as gantry machine position preset and feedback, boring machine, shield machine, coal mine mechanical cylinder position preset and feedback, engineering lifting mechanical cylinder position preset and feedback, Position presetting and feedback of mechanical cylinder in steel mills such as rolling mills, position presetting and feedback of oil cylinder in blow molding, position presetting and feedback of injection molding machinery, adjustment of railway and bridge, detection of water level, control of sluice gates, position presetting and feedback of wood machinery, position presetting and feedback of cylinder level, position presetting and feedback of chemical container level, drinking water and sewage treatment system, Geodetic system, gate opening position preset and feedback, cylinder level measurement.
MTF1/MTF2 Slider type Magnetostrictive displacement sensor Mounting size:
Model Selection:
